SCCTC · Year 2 · Refresher
Laser Fundamentals
Everything from Year 1, in the order you learned it. Keep this page open while we go through the slides.
When a slide turns red with a ★, tap that stop below and try it (about 4 minutes). Then look back up at the slides and we keep going.
Year 1 · Lessons 1–2
Introduction & Laser Safety
Stop 1 · about 4 min
Balloon lab
From Year 1: Lesson 1 · IntroductionLesson 2 · Laser Safety
Remember: on day one, and again in the safety lesson, we aimed lasers at balloons, and only some of them popped. A balloon only heats up from the light it absorbs. Light it reflects does nothing.
Fill in the pop chart. Which balloon lasts longest under the green laser?
Fire every laser at every balloon to fill in the chart.
Simplified model: typical absorption values, not measured for a real balloon. In class, only the presenter runs the high-power lasers, with eyewear rated for them.
Stop 2 · about 5 min
Eye explorer
From Year 1: Lesson 2 · Anatomy of the EyeLaser Safety Glasses
Remember: your eye has a lens that focuses light onto the retina. A laser beam gets focused to a tiny, intense spot there. How far a beam gets into the eye depends on its wavelength.
Builds on ★1: the balloon popped from absorbed light. Your eye absorbs light too.
Slide through the wavelengths. Then complete the three glasses missions.
Try on safety glasses
Each pair is rated for certain wavelengths. Optical density (OD) is how strongly it blocks: each step blocks 10 times more.
Example eyewear, simplified. Real glasses have their OD and wavelength range printed on the frame.
Stop 3 · about 4 min
Class check
From Year 1: Lesson 2 · Laser ClassesPractical Safety
Remember: every laser product has a class on its label, from Class 1 (safe under normal use) to Class 4 (very dangerous). US warning labels are yellow and black.
Builds on ★2: the higher the class, the more your eyes need protecting.
Sort each laser into its class.
Safe or Sorry?
Year 1 · Lesson 3
Laser Optics
Stop 4 · about 5 min
Beam bench
From Year 1: Lesson 3 · Laser Optics
Remember: in Lesson 3 we shone a flashlight and a laser at the wall from 6 ft and 18 ft, then used a convex lens to find the focal point.
Builds on ★2: the lens in your eye is a convex lens too. Now you get to control one.
Part A: which beam spreads more? Part B: drag the card to find the focal point.
Part A · Flashlight vs laser
Both beams spread. Example values: a flashlight with a 20° cone, and a 2 mm laser beam that spreads 1 mm per meter.
Part B · Find the focal point
Drag the card until the red spot is as small as you can get it.
Year 1 · Lesson 4
The Power of the Beam
Stop 5 · about 5 min
Laser engraver
From Year 1: Lesson 4 · Power & Power Density
Remember: in Lesson 4 the IR module left no mark on the wood out of focus, then smoked as soon as we focused it. The power never changed. Only the spot size did.
Builds on ★4: focusing to the beam waist makes the tiny spot. Now see what that tiny spot can do.
Drag your finger on the wood to engrave. Can you write your initials?
Power density = power ÷ area, and area = π × d² ÷ 4 (convert mm to cm first). The point where wood marks (about 100 W/cm² here) is a rough guide, not a measured value.
Year 1 · Lesson 5
The Power of Coherent Light
Stop 6 · about 5 min
Build a laser beam
From Year 1: Lesson 5 · Laser Applications
Remember: in Lesson 5 we named three properties that make laser light different, then engraved your aluminum business cards.
Builds on ★4 and ★5: a narrow beam and a tiny spot are what make lasers so useful.
Start with light-bulb light. Switch on all three properties to turn it into laser light.
Which property does each job depend on most?
End of class · about 5 min
Exit check
From Year 1: Lessons 1–5
Five questions, in the order you learned them. Answer on your own first.
"With knowledge and respect, lasers can do amazing things, safely."